Frequently Asked Questions
What is the difference between the KNX Matter Server and the SmartCore?
The KNX Matter Server connects an existing or planned KNX system to Apple Home, Google Home, Alexa and Home Assistant. The SmartCore is a standalone controller with DALI, 12 relays and 12 inputs that needs no KNX and no ETS. Go to the product finder on the home page to pick the right one in two questions.
What is the difference between the KNX Matter Server and the KNX Bridge?
The KNX Matter Server has the same hardware as the KNX Bridge but only the Matter function. It has no KNX-DALI Gateway, no KNX IP Interface and no Remote Access. You program it with ETS over the KNX TP bus only. Downloads are the same files as for the KNX Bridge.
Should I build my new home on KNX or on DALI?
KNX is recommended for larger houses or when heating, ventilation, access and other systems should be integrated. DALI with the SmartCore suits apartments and lighting-focused projects and is generally cheaper and easier to program.
What do I need to bring my existing KNX house into Apple Home?
One KNX Matter Server in the cabinet with power, network and a KNX connection, an Apple home hub, and ideally the ETS project or a group address export from your installer. With Google Home, Alexa or SmartThings, use a Matter-compatible hub of that ecosystem instead, for example a Google Nest Hub, an Amazon Echo or a Samsung SmartThings hub.
Can I use the KNX Matter Server without a KNX system?
No. The KNX Matter Server always needs a KNX system (at least a KNX power supply) and is programmed with ETS. ETS programs it over the KNX TP bus only. For DALI-only or relay-based projects without KNX, use the SmartCore.
Do my wall switches keep working?
Yes. The KNX installation stays unchanged; the Matter Server only adds app and voice control. Matter is an additional control interface on top of your KNX installation, so your KNX programming, switches and automation logic keep working.
Do I need both a KNX Matter Server and a SmartCore?
Usually not. The KNX Matter Server brings your KNX installation to Matter and has no DALI function. For DALI lights without KNX, use the SmartCore.
How does the KNX Matter Server differ from other KNX-to-Matter gateways?
It is a Matter and HomeKit bridge for KNX in one PoE-powered, low-power embedded device. It also offers a HomeKit mode for accessory types Matter does not yet cover, such as garage doors.
Can Atios products be used in hotels or multi-unit buildings?
Yes. For KNX projects, install a KNX Matter Server in the electrical cabinet of each KNX installation, and pair it by scanning the Matter QR code.
Can I try the interface without buying hardware?
Yes. Try the Web Interface online, without a device, at https://kd.atios.ch/app/.
Can Atios plan and pre-program my KNX project?
Yes. We supply all KNX devices pre-programmed according to your electrical plans; your local electrician installs them and we commission remotely or on site.
How many devices can be added to the Atios KNX Matter Server?
Each accessory (for example a light or a blind) can have as many KNX group addresses as required. When paired with HomeKit, up to 100 accessories are supported (Apple's limit). With Matter there is currently no enforced limit. Installations with about 160 accessories have been confirmed. If you need more, use several Atios KNX Matter Servers paired to the same Apple or Google Home account.
Do Atios devices require an internet connection?
No. Atios devices work on your local network and do not require an internet connection. Matter and KNX also operate locally, so your home continues to function normally even when the internet is down. An internet connection is only needed for remote access via smart home apps when you are away from home and for firmware updates.
My device doesn't start on PoE but works on DC. What now?
Try another PoE switch or injector that meets IEEE 802.3af. In the meantime, you can power the device from the DC input. Never connect PoE and DC together. If the device still does not start on PoE, contact Atios support.
How do I find my device on the network?
Open setup.atios.ch on a device in the same network; it discovers the Atios device even with a changing DHCP address.
The LED blinks green and there's no IP. What now?
A blinking green LED means the device is still establishing its IP connection. Check the network cable and the switch port, and check that your router's DHCP server is running. Then reboot the device. If it still gets no IP address, you can factory reset it: hold the Reset Button for 10 seconds until the LED blinks purple, then release it. A factory reset deletes the configuration of the device, so use it as a last step.
How do I switch to Wi-Fi?
Select Wi-Fi in network settings and reboot; a blinking white LED shows the setup access point. Connect with your phone and enter your 2.4 GHz credentials.
How do I configure HomeKit or Matter?
Go to the KNX Matter Server Pairing Guide. It covers pairing with Matter and with HomeKit.
Should I pair via HomeKit or Matter?
Use Matter if you want Google Home, Alexa, SmartThings or Home Assistant, or more than one app at the same time. Matter is the recommended mode. Use HomeKit only if you use Apple Home alone and need an accessory type that Matter does not cover yet, such as a garage door or an alarm system. Door locks work over Matter. HomeKit and Matter cannot run at the same time, and switching from one to the other resets the pairing.
How do I add a new device after pairing?
Add it in the Accessory Manager, save and reboot. It appears in your app automatically; do not re-pair or remove the Matter Server.
Can I use my KNX scenes in Apple Home?
No. Create scenes in Apple Home instead; they show correct device status and are unlimited. KNX scenes are not exposed to Apple Home, because they do not map cleanly to its interface.
How do I trigger an Apple Home scene from a wall button?
Create a Programmable Switch accessory for the button and assign the scene to the press in Apple Home. First build the scene in Apple Home with the lights, blinds and other accessories you want. Then create an automation that runs the scene when the Programmable Switch is pressed.
Can Matter sensors be used in ETS?
No. Use them in your Matter app and create automations that control KNX devices. Any other Matter-compatible device, such as a door lock, a robot vacuum or a smart plug, can be added to the same app next to the KNX devices. It works independently of KNX.
Can I connect cameras through the KNX Matter Server?
No. Cameras are added directly to Apple Home or Google Home; the Matter Server handles KNX devices only.
Can the KNX Matter Server bring Matter devices into KNX?
No. The KNX Matter Server exposes KNX to Matter apps, and Matter devices do not appear in KNX. The KNX Matter Server is a Matter bridge and not a Matter controller. Matter devices stay in your smart-home app next to the KNX devices, and you link them there with scenes and automations.
Why does Apple Home say the accessory is not certified?
The warning only appears in HomeKit mode, which is built on Apple's official SDK but not HomeKit-certified so that garage doors and alarm systems can be supported. The device is Matter certified, and Matter pairing shows no warning.
Why are all devices in the same room?
Apple Home and SmartThings ask for one room when you pair the Matter Server, and all its accessories start in that room. Move each accessory to its own room in the app. On firmware older than 2.4.50, rooms can collapse into one after an update. Update to the latest stable firmware.
Can a KNX button control a Matter light like Hue?
Not directly. Expose the KNX button as a Programmable Switch and assign the Matter light or scene to it in Apple Home or Google Home.
Where is the slat angle in Apple Home?
Open the blind's accessory settings; the tilt slider is there. Apple does not show it on the main tile.
Which group addresses are required for a blind?
Target and current position in percent, plus target and current tilt for venetian blinds. Movement and stop addresses are optional.
Does the KNX Matter Server control heating itself?
No. Heating logic stays in your KNX actuator or room controller; the Matter Server shows temperature, setpoint and mode in your app.
Can I use a 1-bit heat/cool object instead of DPT 20.102?
Yes, on recent firmware: leave the mode field empty and use the heat/cool and on/off objects.
Can KNX CO2 and humidity sensors be shown in Apple Home?
Yes, on current firmware, as long as the values are on KNX group addresses.
Who creates scenes and makes later adjustments?
Scenes are created directly in the app and can be changed at any time without reprogramming KNX.
Why don't fans appear in Matter on the KNX Matter Server?
Fans are supported in Matter. Add a Fan accessory in the Accessory Manager and enter the KNX group addresses for on/off, rotation speed and swing mode. Only the Alarm and Garage accessories still need HomeKit mode.
Does the KNX Matter Server include a KNX IP Interface?
No. ETS programs the KNX Matter Server over the KNX TP bus only. Use a KNX USB or KNX IP interface on the bus to program it from ETS.
Can I import my ETS project into the KNX Matter Server?
Yes. Open KNX Settings in the Web Interface, select your ETS project file and import it. Then check in the Accessory Manager that the group addresses match your ETS project.
Do I have to program the KNX Matter Server in ETS?
Not for the Matter function. You configure Matter accessories in the Web Interface. You need ETS for KNX Secure and to set the physical address. ETS reaches the device over the KNX TP bus only.
I don't have the ETS project. What now?
Use the Group Monitor in the Web Interface: press a wall switch and copy the group address shown. For complex functions, the project may need to be reconstructed.
Where do I get the ETS product database for the KNX Matter Server?
In the ETS online catalogue or on the Atios downloads page. Use the version matching your firmware. It is the same product database as for the KNX Bridge.
Which datapoint type is used for colour temperature?
DPT 7.600 (Kelvin). Colour uses DPT 232.600.
Can I arm my alarm system from Apple Home?
Yes, if your alarm system has a KNX interface or arm/disarm inputs connected to KNX. The Matter Server shows it as a security system in Apple Home in HomeKit mode.
Which knxprod do I need after updating my KNX Matter Server?
Use the newest product database (knxprod) of the KNX Bridge from the Atios AG entry in the ETS online catalogue, currently 3.1. KNX Secure needs knxprod 3.0 or higher together with firmware 3.1.0 or higher. For a KNX Matter Server that is already in your ETS project, select it, go to Properties, Info, Application, click Update and download the application. Do not change the application with the ComboBox, because that erases the accessories and settings.
Which door locks work?
Use a motorised lock with a control input and a sensor output. Drive the lock with a KNX actuator and enter its group addresses in a Door Lock accessory. Avoid locks that only work over Bluetooth, because they have no wired input.
Can I integrate my door intercom?
Atios devices do not carry video. A door opener that you switch over KNX is added with the Door Lock accessory and its group addresses. A video intercom or camera that supports Matter or HomeKit is added to your smart-home app directly.
Does the device have timers or logic?
Timers and automations are created in your Matter app, which needs a home hub. The KNX Matter Server has no built-in timer.
How do I show a dry contact status?
Use a KNX binary input and add it as a Contact Sensor accessory. Apple Home can then notify you of changes.
Can I set percentage position and slat tilt?
Yes, with a KNX actuator that has position objects. In the Shutter accessory, enter the Position and Position status addresses (DPT 5), plus Tilt Position and Tilt Position status for venetian blinds.
Why do I need to reboot after changing the configuration?
The accessory list is loaded at startup, so changes take effect after Save Configuration and a reboot.
My accessories lost names and automations after a reboot.
Check the firmware under System, About, and update to the latest stable version if it is older. After an update, wait at least 2 minutes before you reboot, because an earlier reboot reverts the firmware. If names are still missing, remove the Matter Server from Apple Home and pair it again.
The ETS download fails. What can I try?
Make sure the KNX bus is powered, program the physical address first and the application separately, and wait two minutes after any firmware update before programming.
The Matter Server does not reach devices on another KNX line.
The line coupler filters the group addresses. Link them to a dummy application in the Matter Server's line in ETS so they pass the filter.
My blinds only open or close fully.
Your actuators probably only have up/down objects. Reprogram them with absolute position and status objects for full control.
My AC turns off a second after switching it on.
Recreate the thermostat accessory without the 'sends DPT 1.001 (On/Off)' option unless your AC's KNX gateway needs it. With this option on, mode mappings are ignored.
My KNX lights switch but do not dim. What is missing?
Check that the Lightbulb accessory uses a channel setting with dimming: Dimmable, Tunable White or Colour. For Dimmable, enter the Dimming address (brightness in percent) and the Dimming status address, as well as the Switching and Switching status addresses. Click Save Configuration and reboot the KNX Matter Server.
How do I factory reset the device?
Press and hold the Reset Button for 10 seconds until the Power LED blinks purple, then release. The LED turns solid purple while the device resets. You can also use Factory Reset in the Web Interface under System Settings. A factory reset deletes all configuration and pairings, so export your configuration first.
My device is stuck in a boot loop. What can I do?
Look at the Power LED: solid blue means the device is booting. Power the device from a PoE port or DC supply and test the network cable. If the device keeps rebooting, hold the Reset Button during boot until the LED is solid yellow. This enters safe mode. If the device does not recover, contact support with the serial number.
Why does my update revert after rebooting?
After installing, the device needs 2 minutes to confirm the new firmware. Rebooting earlier reverts to the previous version.
Can I roll back a firmware update?
Yes, the previous version can be restored. Contact support with your serial number if you need a specific version.
My device reboots or freezes after an update. What should I do?
Update to the newest firmware first. If the problem continues, start Debug in System Settings and export your configuration. Then contact support with the serial number and the debug log. After an update, wait at least 2 minutes before you reboot.
How do I back up my configuration?
Open System Settings in the Web Interface and export the configuration. To restore it, import the file in the same place.
Can my installer or Atios access my home?
Atios has no access to your home. Control is local and encrypted, and only people you invite in your Home app can control it. Your installer cannot see or control your home through the app unless you share it with them.
Does the KNX Matter Server support KNX Secure?
Yes, IP Secure and Data Secure on current firmware. Existing devices can be upgraded by firmware update.
Do you offer white-label or OEM versions?
Yes. White-label versions of our gateways are possible from a minimum order quantity, and we also license our Matter, DALI-2 and KNX software stacks. Contact us with your use case and expected volumes.
These questions are the same on every Atios device FAQ page.
Matter & Apps
What is Matter?
Matter is an open smart home standard that lets all Matter-certified devices work together over one protocol. Apple, Google, Amazon, Samsung and Philips back it, and it works with Apple Home, Google Home, Samsung SmartThings and Alexa, so you can choose your platform.
What's the difference between a Matter controller and a Matter bridge?
Matter controller: manages Matter devices, provides user interfaces, and executes automations and scenes. Controllers are typically platform-specific (e.g. Apple HomePod works with Apple Home, Google Nest Hub works with Google Home).
Matter bridge: translates other systems and protocols (for example Zigbee or Z-Wave) into Matter, making those devices accessible to controllers. A bridge does not provide a user interface or control function on its own.
Atios devices that connect to Matter act as Matter bridges. You also need a Matter controller (HomePod, Nest Hub, Echo, etc.) from your chosen ecosystem.
Note: Some products can be both a controller and a bridge simultaneously.
Is there an Atios app?
No. Atios devices work with existing apps such as Apple Home, Google Home, Alexa, SmartThings and Home Assistant.
Do I need a HomePod or Apple TV?
Not for local control from your iPhone. You need one for remote access, automations and sharing the home with others.
Do I need a hub for Google Home?
Yes, Google Home needs a Matter-capable Nest device to add and control Matter devices.
Does it work with Homey and SmartThings?
Yes. SmartThings and Homey Pro are both Matter controllers, so you pair the Atios device with Matter.
Do I need a Thread Border Router?
No. Atios devices connect to Matter through your home network, not through Thread. You only need a Matter-compatible hub (HomePod, Google Nest, Echo, etc.).
How do I use Apple Home and Google Home at the same time?
Pair with the first app via Matter, then use its 'pair another app' function to get a new code for the second app. Do not scan the original QR code again. Matter's multi-admin feature lets one Atios device work in several apps at the same time. Each app keeps its own automations and scenes, which do not sync between the apps.
Can one device serve two apartments as separate homes?
No. One unit is one Matter bridge, and every home or app you pair it with sees all of its accessories. Two separate apartments need two units.
The QR code is not accepted. What can I do?
Enter the numeric pairing code from the Web Interface manually. If the device was paired before, reset the pairing first.
Google Home says 'Unable to add bridge'. What should I check?
Make sure you have a Matter-capable Google hub, the device rebooted less than 15 minutes ago, and your phone and the device are in the same subnet without blocked mDNS. Update the device to the latest firmware first.
Firmware & Troubleshooting
How do I report a bug or request a feature?
Send bugs to the support mailbox and post feature ideas on the Atios subreddit.
Privacy & Security
What data is sent to Atios?
Only connection data such as IP address, serial number and firmware version at reboot and update checks. No usage or home data, and the device works if blocked from the internet. The connection data is encrypted and never shared. Go to our Privacy Policy for details.
Pricing & Warranty
Do I have to pay monthly fees?
No. There are no subscription or monthly fees of any kind.
Are firmware updates free?
Yes. All software and firmware updates are free of charge.
Do I get a warranty?
Yes. All Atios products come with a 3-year warranty. Within this period, the item will be repaired, replaced, or credited according to our terms and conditions. Please contact us to claim your warranty.
My device arrived damaged. What should I do?
Send photos and the serial number to support. Atios offers a replacement, repair or partial refund.
How do I return a product?
You can return products within 100 days. Contact support with your order number and we send you the correct return address (EU or Switzerland). After we receive and check the device, the refund is issued to your original payment method, usually within two weeks.
Why does the shop show a higher price than I expected?
The Swiss shop shows prices including Swiss VAT. When you enter a delivery address outside Switzerland at checkout, Swiss VAT is removed and the correct price for your country is applied.
Are project prices available?
Yes, volume pricing applies for multi-unit projects; contact Atios with unit count and a sample room list.
Ordering & Shipping
How fast do you ship?
Products in stock ship within 1-2 working days after payment, with tracking by email. EU orders ship from Germany, others from Switzerland.
Do you ship outside Europe, and who pays duties?
Yes, we ship worldwide, usually by UPS with tracking. Import duties, tariffs and local taxes are charged by the carrier or customs in your country and are paid by the recipient. We cannot predict the exact amount, as it depends on your country's rules.
Will I pay customs or import VAT when ordering from the EU?
EU orders are shipped from our warehouse in Germany, so there are no customs formalities or import VAT on delivery. Only shipments sent from Switzerland are charged import VAT and a handling fee by the courier. If you are unsure where your order ships from, contact us before ordering.
I have an EU VAT ID. Can I buy without VAT?
Yes. Business customers with a valid EU VAT ID can be invoiced under the reverse-charge procedure and account for VAT in their own country. Enter your VAT ID at checkout or ask us for an invoice; German business customers receive an invoice with German VAT.
Which HS code should I use for customs?
Contact us for the HS code of each product and for a commercial invoice if your customs broker needs one.
My parcel is held at customs. What should I do?
Forward the carrier's or customs office's message to support so we can supply the required documents directly. Most holds are resolved by providing invoice details or a product description.
Can I buy through my electrical wholesaler?
Yes, our products are listed at several electrical wholesalers. If yours does not stock them yet, order directly from us and we can deliver to your wholesaler or to site.
Partners & Resellers
Is there an installer near me who knows Atios products?
Contact us with your location and project details and we connect you with a partner or distributor in your area. Where we have no partner yet, any qualified electrician can install our products, and we support them remotely.
Does Atios install or commission systems itself?
We offer remote commissioning via screen sharing for a flat fee or hourly rate, and for larger projects we can come on site or work with partner installers.
Why must I buy through a local distributor in my country?
In some countries we work with an exclusive distributor who handles sales, stock and local support. They can also help you find a certified integrator.
Do you have installer or integrator pricing?
Yes. Professionals get a discounted first sample via a voucher in our shop, volume discounts from 3 and 10 units, and project pricing for larger orders. Contact us with your company details to receive your terms.
Can I get a free demo unit?
We don't offer free or loan units, but professionals can buy a sample with a discount voucher and return it for a full refund within the return period if it is not a fit.
Is there a B2B portal?
Partners order by email with a pro forma invoice. Contact us for partner access.
How can my company become an Atios distributor?
Contact us with your country, your current product portfolio and expected volumes. We first check whether an existing partner covers your territory, then usually start with a discounted sample and a call about cooperation.
Do distributors get exclusivity?
Exclusivity is granted case by case depending on market commitment and volumes. In several countries we work non-exclusively with multiple partners.
Where can partners get flyers and product data?
Partners get access to a shared marketing folder with current flyers, datasheets and product images. Digital flyers can be localized with your logo; printed flyers can ship with your order.
How do I list Atios products at my wholesaler?
Send us the wholesaler's article-creation form and we fill in item numbers, EANs, images and datasheets so the products can be listed.